U-Boot 2010.09 (Jan 10 2011 - 20:12:00)
DRAM: 64 MiB
## Unknown FLASH on Bank 1 - Size = 0x00000000 = 0 MB
Flash: 0 Bytes
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x80000, size 0x790000
7929856 bytes read: OK
## Booting kernel from Legacy Image at 70400000 ...
Image Name: Linux Kernel Image
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2370280 Bytes = 2.3 MiB
Load Address: 70008000
Entry Point: 70008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.36-rc6 (user@debian) (gcc version 4.6.1 (Sourcery CodeBench Li
te 2011.09-70) ) #1 Sat Sep 8 16:47:28 EDT 2012
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Atmel AT91SAM9G45-EKES
Ignoring unrecognised tag 0x54410009
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 400 MHz, master 133 MHz, main 12.000 MHz
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200 ubi.mtd=1 root=ubi0:nandfs rw rootfsty
pe=ubifs
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60444k/60444k available, 5092k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffa00000 - 0xffe00000 ( 4 MB)
vmalloc : 0xc4800000 - 0xfee00000 ( 934 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc002b000 ( 140 kB)
.text : 0xc002b000 - 0xc0412000 (3996 kB)
.data : 0xc042a000 - 0xc044e400 ( 145 kB)
Hierarchical RCU implementation.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:192
AT91: 160 gpio irqs in 5 banks
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.0: using pins 52 (SDA) and 53 (SCL)
Advanced Linux Sound Architecture Driver Version 1.0.23.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource pit
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
msgmni has been set to 118
io scheduler noop registered (default)
atmel_lcdfb atmel_lcdfb.0: backlight control is not available
atmel_lcdfb atmel_lcdfb.0: 510KiB frame buffer at 73900000 (mapped at ffa00000)
Console: switching to colour frame buffer device 60x34
atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00500000 (mapped at c4814000), i
rq 23
atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL
atmel_usart.2: ttyS2 at MMIO 0xfff90000 (irq = 8) is a ATMEL_SERIAL
brd: module loaded
loop: module loaded
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bi
t)
Scanning device for bad blocks
Creating 2 MTD partitions on "atmel_nand":
0x000000000000-0x000004000000 : "Partition 1"
0x000004000000-0x000010000000 : "Partition 2"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: max. sequence number: 8
UBI error: vtbl_check: volume table check failed: record 0, error 9
UBI error: ubi_init: cannot attach mtd1
atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000 (irq 14)
MACB_mii_bus: probed
eth0: Atmel MACB at 0xfffbc000 irq 25 (00:1f:f2:00:00:00)
eth0: attached PHY driver [Micrel KS8001 or KS8721] (mii_bus:phy_addr=ffffffff:0
1, irq=-1)
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt73usb
usbcore: registered new interface driver rt2800usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
atmel-ehci atmel-ehci: Atmel EHCI UHP HS
atmel-ehci atmel-ehci: new USB bus registered, assigned bus number 1
atmel-ehci atmel-ehci: irq 22, io mem 0x00800000
atmel-ehci atmel-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 2
at91_ohci at91_ohci: irq 22, io mem 0x00700000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
USB Serial support registered for moto-modem
usbcore: registered new interface driver moto-modem
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
atmel_usba_udc atmel_usba_udc: MMIO registers at 0xfff78000 mapped at c4872000
atmel_usba_udc atmel_usba_udc: FIFO at 0x00600000 mapped at c4900000
mice: PS/2 mouse device common for all mice
rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0
rtc-at91sam9 at91_rtt.0: rtc0: SET TIME!
i2c /dev entries driver
at_hdmac at_hdmac: Atmel AHB DMA Controller ( cpy slave ), 8 channels
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
atmel_ac97c atmel_ac97c.0: Atmel AC97 controller at 0xc4888000, irq = 24
ALSA device list:
#0: Atmel AC97 controller
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock
UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi0:nandfs", error -19
VFS: Cannot open root device "ubi0:nandfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00 65536 mtdblock0 (driver?)
1f01 196608 mtdblock1 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[<c003169c>] (unwind_backtrace+0x0/0xf0) from [<c0328cc8>] (panic+0x58/0x174)
[<c0328cc8>] (panic+0x58/0x174) from [<c0008ea4>] (mount_block_root+0x1d4/0x294)
[<c0008ea4>] (mount_block_root+0x1d4/0x294) from [<c0009150>] (prepare_namespace
+0x8c/0x1bc)
[<c0009150>] (prepare_namespace+0x8c/0x1bc) from [<c0008b94>] (kernel_init+0x10c
/0x144)
[<c0008b94>] (kernel_init+0x10c/0x144) from [<c002cdb0>] (kernel_thread_exit+0x0
/0x8) |
15.10.2012 19:22
15.10.2012 19:32
