/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian.pop@leadtechdesign.com>
* Lead Tech Design <www.leadtechdesign.com>
*
* Configuation settings for the AT91SAM9260EK & AT91SAM9G20EK boards.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* SoC must be defined first, before hardware.h is included.
* In this case SoC is defined in boards.cfg.
*/
#include <asm/hardware.h>
/*
* Warning: changing CONFIG_SYS_TEXT_BASE requires
* adapting the initial boot program.
* Since the linker has to swallow that define, we must use a pure
* hex number here!
*/
#define CONFIG_SYS_TEXT_BASE 0x21D00000
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* main clock xtal */
#define CONFIG_SYS_HZ 1000
/* Define actual evaluation board type from used processor type */
#ifdef CONFIG_AT91SAM9G20
# define CONFIG_AT91SAM9G20EK /* It's an Atmel AT91SAM9G20 EK */
#else
# define CONFIG_AT91SAM9260EK /* It's an Atmel AT91SAM9260 EK */
#endif
/* Misc CPU related */
#define CONFIG_ARCH_CPU_INIT
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_DISPLAY_CPUINFO
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
#define CONFIG_AT91_GPIO
#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 }
/* LED */
#define CONFIG_AT91_LED
#define CONFIG_RED_LED AT91_PIN_PA9 /* this is the power led */
#define CONFIG_GREEN_LED AT91_PIN_PA6 /* this is the user led */
#define CONFIG_BOOTDELAY 3
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE 1
#define CONFIG_BOOTP_BOOTPATH 1
#define CONFIG_BOOTP_GATEWAY 1
#define CONFIG_BOOTP_HOSTNAME 1
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_BDI
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_SOURCE
#define CONFIG_CMD_PING 1
#define CONFIG_CMD_DHCP 1
//#define CONFIG_CMD_NAND 1
#define CONFIG_CMD_USB 1
/*
* SDRAM: 1 bank, min 32, max 128 MB
* Initialized before u-boot gets started.
*/
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1
#define CONFIG_SYS_SDRAM_SIZE 0x02000000
/*
* Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
* leaving the correct space for initial global data structure above
* that address while providing maximum stack area below.
*/
#ifdef CONFIG_AT91SAM9XE
# define CONFIG_SYS_INIT_SP_ADDR \
(ATMEL_BASE_SRAM + 0x1000 - GENERATED_GBL_DATA_SIZE)
#else
# define CONFIG_SYS_INIT_SP_ADDR \
(ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)
#endif
/* DataFlash */
#define CONFIG_ATMEL_DATAFLASH_SPI
#define CONFIG_HAS_DATAFLASH 1
#define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ)
#define CONFIG_SYS_MAX_DATAFLASH_BANKS 2
#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */
#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 0xD0000000 /* CS1 */
#define AT91_SPI_CLK 4800000
#ifdef CONFIG_AT91SAM9G20EK
#define DATAFLASH_TCSS (0x22 << 16)
#else
#define DATAFLASH_TCSS (0x1a << 16)
#endif
#define DATAFLASH_TCHS (0x1 << 24)
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
#define CONFIG_SYS_NAND_DBW_8
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13
#endif
/* NOR flash - no real flash on this board */
#define CONFIG_SYS_NO_FLASH 1
/* Ethernet */
#define CONFIG_MACB 1
#define CONFIG_RMII 1
#define CONFIG_NET_MULTI 1
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RESET_PHY_R 1
/* USB */
#define CONFIG_USB_ATMEL
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_DOS_PARTITION 1
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 /* AT91SAM9260_UHP_BASE */
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
#define CONFIG_USB_STORAGE 1
#define CONFIG_CMD_FAT 1
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END 0x23e00000
#ifdef CONFIG_SYS_USE_DATAFLASH_CS0
/* bootstrap + u-boot + env + linux in dataflash on CS0 */
#define CONFIG_ENV_IS_IN_DATAFLASH 1
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400)
#define CONFIG_ENV_OFFSET 0x4200
#define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET)
#define CONFIG_ENV_SIZE 0x4200
#define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x22000000 0x210000; bootm"
#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
"root=/dev/mtdblock0 " \
"mtdparts=atmel_nand:-(root) " \
"rw rootfstype=jffs2"
#elif CONFIG_SYS_USE_DATAFLASH_CS1
/* bootstrap + u-boot + env + linux in dataflash on CS1 */
#define CONFIG_ENV_IS_IN_DATAFLASH 1
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + 0x8400)
#define CONFIG_ENV_OFFSET 0x4200
#define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + CONFIG_ENV_OFFSET)
#define CONFIG_ENV_SIZE 0x4200
#define CONFIG_BOOTCOMMAND "cp.b 0xD0042000 0x22000000 0x210000; bootm"
#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
"root=/dev/mtdblock0 " \
"mtdparts=atmel_nand:-(root) " \
"rw rootfstype=jffs2"
#else /* CONFIG_SYS_USE_NANDFLASH */
/* bootstrap + u-boot + env + linux in nandflash */
#define CONFIG_ENV_IS_IN_NAND 1
#define CONFIG_ENV_OFFSET 0x60000
#define CONFIG_ENV_OFFSET_REDUND 0x80000
#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xA0000 0x200000; bootm"
#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
"root=/dev/mtdblock5 " \
"mtdparts=atmel_nand:128k(bootstrap)ro," \
"256k(uboot)ro,128k(env1)ro," \
"128k(env2)ro,2M(linux),-(root) " \
"rw rootfstype=jffs2"
#endif
#define CONFIG_SYS_PROMPT "U-Boot> "
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP 1
#define CONFIG_CMDLINE_EDITING 1
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128
24, 0x1000)
#define CONFIG_STACKSIZE (32
24) /* regular stack */
#ifdef CONFIG_USE_IRQ
#error CONFIG_USE_IRQ not supported
#endif
#endif
09.07.2011 00:22
