RomBOOT

>Start AT91Bootstrap...

Copy application ...

Run ...



U-Boot 1.1.5 (Apr 29 2008 - 20:23:52)

DRAM: 64 MB
NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xda ( NAND 256MiB 3,3V 8-bit)
NAND: Pagesize: 2048, Blocksize: 128K, OOBsize: 64
256 MiB
DataFlash:AT45DB321
Nb pages: 8192
Page Size: 528
Size= 4325376 bytes
Logical address: 0xC0000000
Area 0: C0000000 to C0003FFF (RO)
Area 1: C0004000 to C0007FFF
Area 2: C0008000 to C0037FFF (RO)
Area 3: C0038000 to C041FFFF
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
KS8721 PHY Detected

ETH: 100M Full Duplex.

End of Autonegociation

Hit any key to stop autoboot: 3  0
U-Boot> setenv ipaddr 10.10.3.33; setenv serverip 10.10.3.17; tftpboot 20800000 ipl; bootm 20800000

TFTP from server 10.10.3.17; our IP address is 10.10.3.33
Filename 'ipl'.
Load address: 0x20800000
Loading: *#################################################################
#################################################################
#################################################################
#########################################################
done
Bytes transferred = 1286355 (13a0d3 hex)
## Booting image at 20800000 ...
Image Name: QNX6 Kernel Image
Image Type: ARM QNX Kernel Image (gzip compressed)
Data Size: 1286291 Bytes = 1.2 MB
Load Address: 20000000
Entry Point: 20000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...
¤
AT91SAM9260 hardware init done.
AT91SAM9260 QNX IPL

Scanning... Found image. Jump to Startup.

Dcache: 256x32 WB
Icache: 256x32
arm926 rev 5 24MHz
Welcome to QNX Neutrino 6.3.2 AT91SAM9260 board
Starting USART driver...

create device:  /dev/ser1
create device: /dev/ser2
create device: /dev/ser3
create device: /dev/ser4
create device: /dev/ser5.
Starting ethernet driver...

Process 5 (ifconfig) exited status=0.
Starting USB driver...
Starting SD/MMC driver...
Trying to mount all mass storage devices
mmc_attach failed
xpt_configure: No sd interfaces found

Process 4105 (devb-sd-at91sam9260) exited status=0.
Path=0 - QNX USB Storage
target=0 lun=0 Direct-Access(0) - Generic USB2.0 Rev: %z!Y
Unable to access "/dev/hd1" (2)
mount: Can't mount /fs/usb (type dos)
mount: Possible reason: Invalid argument

Process 8201 (mount) exited status=1.
mount: Can't mount /fs/sd (type dos)
mount: Possible reason: Invalid argument

Process 24585 (mount) exited status=1.
mount: Can't mount /fs/sd (type dos)
mount: Possible reason: Invalid argument

Process 40969 (mount) exited status=1.
# ls /dev

console null ptyp4 ser2 socket ttyp3 zero
hd0 pipe ptyp5 ser3 text ttyp4
hd0t14 ptyp0 ptyp6 ser4 tty ttyp5
io-net ptyp1 ptyp7 ser5 ttyp0 ttyp6
io-usb ptyp2 sem shmem ttyp1 ttyp7
mem ptyp3 ser1 slog ttyp2 tymem

Process 77833 (ls) exited status=0.
# mount -t dos /dev/hd0t14 /fs/usb


Process 86025 (mount) exited status=0.
# ls -l /fs/usb

total 3955
drwxrwxrwx 4 root root 16384 Aug 18 2008 .
drwxrwxrwx 4 root root 16384 Aug 18 2008 ..
n--------- 1 root root 0 Aug 18 2008 =SONY
drwxrwxrwx 2 root root 4096 Dec 20 2007 inkubus_sukkubus
-rw-rw-rw- 1 root root 1983871 Dec 13 2008 p1030671.jpg

Process 122889 (ls) exited status=0.
#